Stella 120mm Dual Ring ARGB Fan € 10.22 56 in stock	Add to Basket
More variations available Show

Gelid Solutions Stella 120mm Dual Ring ARGB Fan

The STELLA is truly stellar, it features dual ring RGB lighting, a wide RPM range and sturdy dual ball bearings.

Features

Dual ring RGB lighting
Airflow optimised
Double ball bearings
Wide PWM range - 500 to 1600 RPM
35.0 dB(A) / 1600 RPM / 70.0 CFM

STELLA introduces a perfect mixture of top-notch technologies and vivid design. It comes with 8 hub-mounted ARGB LEDs and 16 frame-mounted independent ARGB LEDs to illuminate stylish Dual Ring Lighting. The fan also boasts Double Ball Bearing for improved reliability and optimised impeller for enhanced airflow. Vibrant lights, robust build and low-noise operation all make STELLA a worthy companion for any PC rig.

24 ARGB LEDs: High-bright individually addressable LEDs for a stunningly vivid RGB Lighting experience.

Dual Ring Lighting: Limitless dynamic color modes and RGB effects via independent hub-mounted and ring-mounted LED arrays.

Airflow Optimised: The new optimised blade for higher airflow and lesser noise.

Noiseless Motor Drive IC: Enhanced motor driver circuitry to eliminate clicking noise.

Double Ball Bearing: Carefully selected top-quality ball bearings for ultra-durable operation.

Wide Range RPM: Extended speed range 500 – 1600 RPM.

Broad Compatibility: All modern motherboards with RGB Sync controls and 5V Addressable RGB (ARGB) headers are supported.

Specifications	Stella ARGB 120mm
Model number	FN-Stella-01
Size	120x120x25 mm
Airflow	70 CFM
Bearing	Double Ball Bearing
Cable Length (mm)	500 (PWM & RGB)
Power Draw (W)	5 max
Fan Life Time MTTF at 40C (h)	100,000
Rotational Speed (±10%)	1600 RPM
Min Rotational Speed (±10%)	500 RPM
Noise Level	35 dBA
Static pressure	1.3 mm H₂O
Connector	4-pin PWM
RGB	Yes
RGB LED Connector	3-Pin Addressable RGB Header (5V)
Voltage	12 V
Weight (g)	156
Included	4 Screws
Warranty	24 months
EAN barcode	4897025782518

Specifications	Stella ARGB 120mm
Model number	FN-Stella-01
Size	120x120x25 mm
Airflow	70 CFM
Bearing	Double Ball Bearing
Cable Length (mm)	500 (PWM & RGB)
Power Draw (W)	5 max
Fan Life Time MTTF at 40C (h)	100,000
Rotational Speed (±10%)	1600 RPM
Min Rotational Speed (±10%)	500 RPM
Noise Level	35 dBA
Static pressure	1.3 mm H₂O
Connector	4-pin PWM
RGB	Yes
RGB LED Connector	3-Pin Addressable RGB Header (5V)
Voltage	12 V
Weight (g)	156
Included	4 Screws
Warranty	24 months
EAN barcode	4897025782518

Product Resources

Gelid website

FAQ

How do I measure fan size?
The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

Screw hole spacings and fan sizes

Space Between Screw Holes Fan Size

32mm 40mm

40mm 50mm

50mm 60mm

60mm 70mm

72mm 80mm

83mm 92mm

105mm 120mm
I received a small cable (resistor) with my fan; what is it for?
The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.
How can I tell which way the air blows through the fan?
Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.
Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?
Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.