MenuSearch | Country: Germany | Currency: EUR
NF-S12 800 RPM 120mm Quiet Case Fan
Discontinued
More variations available Show

Noctua NF-S12 800 RPM 120mm Quiet Case Fan

NF-S12 800 RPM 120mm Quiet Case Fan
NF-S12 800 RPM 120mm Quiet Case Fan

Reviews

  • Driver Heaven

    The NF-S12-800 actually didn’t let the temperatures get any higher than when using the Cooler Master stock fans. To think a short while ago I considered the Cooler Master fans quiet!

  • SilentPCReview.com

    The best fan of the bunch was the Noctua, which overcame our scepticism and lived up to its hype by producing more airflow at lower speeds. Its airflow-to-noise ratio is its best feature, which gives it enough of an edge to make up for its slightly rougher noise character. The Noctua has seen recommendations around the web, and we have no qualms about adding our own to the list.

SpecificationsNF-S12 800
Fan size (edge to edge)120mm
ManufacturerNoctua
ModelNF-S12-800
Air volume at full speed (12V), CFM ±10%35
Noise level at full speed (12V), dB(A)8
Fan speed at full speed (12V), RPM ±10%800
Air volume at reduced speed (7.5V), CFM ±10%20
Noise level at reduced speed (7.5V), dB(A)
Fan speed at reduced speed (7.5V), RPM ±10%500
Power consumption, W0,60
Weight, g120
Approximate cable length, cm40
Life expectancy @ 25°C continuous use
150.000 h
Power connector3 and 4 pin
Bearing typeSSO-Bearing
Mounting hardware included4 Vibration Compensators, 4 Fan Screws
Fan depth25mm
Rated voltage6-13V
AccessoriesUltra-Low-Noise Adaptor (U.L.N.A.)
Warranty72 months
EAN barcode4716123312260
SpecificationsNF-S12 800
Fan size (edge to edge)120mm
ManufacturerNoctua
ModelNF-S12-800
Air volume at full speed (12V), CFM ±10%35
Noise level at full speed (12V), dB(A)8
Fan speed at full speed (12V), RPM ±10%800
Air volume at reduced speed (7.5V), CFM ±10%20
Noise level at reduced speed (7.5V), dB(A)
Fan speed at reduced speed (7.5V), RPM ±10%500
Power consumption, W0,60
Weight, g120
Approximate cable length, cm40
Life expectancy @ 25°C continuous use
150.000 h
Power connector3 and 4 pin
Bearing typeSSO-Bearing
Mounting hardware included4 Vibration Compensators, 4 Fan Screws
Fan depth25mm
Rated voltage6-13V
AccessoriesUltra-Low-Noise Adaptor (U.L.N.A.)
Warranty72 months
EAN barcode4716123312260

Customer Reviews

Golden silence!

,

Best 120mm fan, I have ever used. Super silent. Well recommended!

Quality kit

,

A nice weighty, solid feeling fan unit. Even screwed directly to the metal side panel there is no vibration noise, and it runs whisper quiet. Shifts enough air for all but the most extreme overclockers! Comes with silicone mounts for standard mountings, and the braided cable has a nice quality feel to it as well. I might well replace the other fans in the system with some more of these. Recommended!

Product Resources

FAQ

  • How do I measure fan size?

    The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

    As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

    If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

    Screw hole spacings and fan sizes

    Space Between Screw Holes Fan Size
    32mm 40mm
    40mm 50mm
    50mm 60mm
    60mm 70mm
    72mm 80mm
    83mm 92mm
    105mm 120mm
  • I received a small cable (resistor) with my fan; what is it for?

    The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.

  • How can I tell which way the air blows through the fan?

    Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.

  • Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?

    Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

    The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

    Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.

Top Quiet Fans

Recently Viewed Products